S-25C128A Datasheet PDF - Seiko Instruments


www.Datasheet-PDF.com

S-25C128A
Seiko Instruments

Part Number S-25C128A
Description SPI SERIAL E2PROM
Page 30 Pages

S-25C128A datasheet pdf
View PDF for PC
S-25C128A pdf
View PDF for Mobile


No Preview Available !

S-25C128A
www.sii-ic.com
© SII Semiconductor Corporation, 2009-2015
SPI SERIAL E2PROM
Rev.4.2_02_H
The S-25C128A is a SPI serial E2PROM which operates at high speed, with low current consumption and the wide range
operation. The S-25C128A has the capacity of 128 K-bit and the organization of 16384 words × 8-bit. Page write and
sequential read are available.
Features
Operating voltage range:
Read
Write
1.6 V to 5.5 V
1.7 V to 5.5 V
Operation frequency:
Write time:
SPI mode (0, 0) and (1, 1)
Page write:
Sequential read
Write protect:
Protect area:
5.0 MHz (VCC = 2.5 V to 5.5 V)
5.0 ms max.
64 bytes / page
Software, Hardware
25%, 50%, 100%
Monitors write to the memory by a status register
Function to prevent malfunction by monitoring clock pulse
Write protect function during the low power supply voltage
CMOS schmitt inputCS , SCK, SI, WP , HOLD
Endurance:
106cycles / word*1 (Ta = +25°C)
Data retention:
100 years (Ta = +25°C)
Memory capacity:
128 K-bit
Initial delivery state:
FFh, SRWD = 0, BP1 = 0, BP0 = 0
Operation temperature range:
Ta = 40°C to +85°C
Lead-free (Sn 100%), halogen-free*2
*1. For each address (Word: 8-bit)
*2. Refer to “Product Name Structure” for details.
Packages
8-Pin SOP (JEDEC)
8-Pin TSSOP
Caution This product is intended to use in general electronic devices such as consumer electronics, office
equipment, and communications devices. Before using the product in medical equipment or
automobile equipment including car audio, keyless entry and engine control unit, contact to SII
Semiconductor Corporation is indispensable.
1



No Preview Available !

SPI SERIAL E2PROM
S-25C128A
Pin Configurations
1. 8-Pin SOP (JEDEC)
8-Pin SOP (JEDEC)
Top view
18
27
36
45
Figure 1
S-25C128A0I-J8T1U3
Rev.4.2_02_H
Table 1
Pin No. Symbol
Description
1
CS *1
Chip select input
2 SO Serial data output
3
WP *1
Write protect input
4
GND
Ground
5 SI*1 Serial data input
6
SCK*1
Serial clock input
7 HOLD *1 Hold input
8
VCC
Power supply
*1. Do not use it in high impedance.
2. 8-Pin TSSOP
8-Pin TSSOP
Top view
18
27
36
45
Figure 2
S-25C128A0I-T8T1U3
Table 2
Pin No. Symbol
Description
1
CS *1
Chip select input
2 SO Serial data output
3
WP *1
Write protect input
4
GND
Ground
5 SI*1 Serial data input
6
SCK*1
Serial clock input
7 HOLD *1 Hold input
8
VCC
Power supply
*1. Do not use it in high impedance.
Remark Refer to the “Package drawings” for the details.
2



No Preview Available !

Rev.4.2_02_H
Block Diagram
Voltage Detector
CS
SCK
SI
HOLD
WP
SO
Clock Counter
Data Register
Mode
Decoder
Output
Control
Circuit
Address Register
Status Register
Read Circuit
VCC
GND
Figure 3
SPI SERIAL E2PROM
S-25C128A
Step-up Circuit
Page Latch
Memory
Cell
Array
Status
Memory Cell Array
Y Decoder
3



No Preview Available !

SPI SERIAL E2PROM
S-25C128A
Rev.4.2_02_H
Absolute Maximum Ratings
Item
Power supply voltage
Input voltage
Output voltage
Operation ambient temperature
Storage temperature
Symbol
VCC
VIN
VOUT
Topr
Tstg
Table 3
Absolute Maximum Rating
0.3 to + 6.5
0.3 to + 6.5
0.3 to VCC + 0.3
40 to +85
65 to +150
Unit
V
V
V
°C
°C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
Recommended Operating Conditions
Item
Power supply voltage
High level input voltage
Low level input voltage
Table 4
Symbol
Condition
VCC
Read Operation
Write Operation
VIH VCC = 1.6 V to 5.5 V
VIL VCC = 1.6 V to 5.5 V
Ta = 40°C to +85°C
Min. Max.
1.6 5.5
1.7 5.5
0.7 × VCC
0.3
VCC + 1.0
0.3 × VCC
Unit
V
V
V
V
Pin Capacitance
Item
Input capacitance
Output capacitance
Symbol
Table 5
Condition
(Ta = +25°C, f = 1.0 MHz, VCC = 5.0 V)
Min.
Max.
Unit
CIN
COUT
VIN = 0 V ( CS , SCK, SI, WP , HOLD )
VOUT = 0 V (SO)
8 pF
10 pF
Endurance
Item Symbol
Endurance
NW
*1. For each address (Word: 8-bit)
Table 6
Operation Ambient Temperature
Ta = +25°C
Min.
106
Max.
Unit
cycles / word*1
Data Retention
Item
Data retention
Symbol
Table 7
Operation Ambient Temperature
Ta = +25°C
Min.
100
Max.
Unit
year
4




S-25C128A datasheet pdf
Download PDF
S-25C128A pdf
View PDF for Mobile


Similiar Datasheets : S-25C128A S-25C128A S-25C128AxxH

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Privacy Policy + Contact