M-FIAM3M11 Datasheet PDF - Vicor Corporation

www.Datasheet-PDF.com

M-FIAM3M11
Vicor Corporation

Part Number M-FIAM3M11
Description Military 270Vin Filter Input Attenuator Module
Page 4 Pages


M-FIAM3M11 datasheet pdf
Download PDF
M-FIAM3M11 pdf
View PDF for Mobile

No Preview Available !

45
Features
EMI filtering-MIL-STD-461E
Transient protection-MIL-STD-704E
Environments-MIL-STD-810, MIL-STD-202
Environmental stress screening
Low profile mounting options
Output current up to 3 Amps
Mini sized package
Inrush current limiting
M-FIAM3
Military 270Vin Filter
Input Attenuator Module
Shown actual size:
2.28 x 2.2 x 0.5 in
57,9 x 55,9 x 12,7 mm
Product Highlights
The M-FIAM3 is a DC front-end module
that provides EMI filtering and transient
protection required in military applications.
The M-FIAM3 enables designers using
Vicor 2nd Generation 300V DC-DC converters
to meet conducted emission/conducted
susceptibility per MIL-STD-461E; and
input transients per MIL-STD-704E. The
M-FIAM3 accepts an input voltage of
180-375Vdc and delivers output current
up to 3 Amps.
M-FIAM3 is housed in an industry
standard "half brick" module measuring
2.28" x 2.2" x 0.5" and depending upon
model selected, may be mounted on-board
or in-board for height critical applications.
Absolute Maximum Rating
Parameter
+In to –In
+In to –In
Mounting torque
Pin Soldering temperature
Pin Soldering temperature
Operating temperature H–Grade
Storage temperature H–Grade
Operating temperature M–Grade
Storage temperature M–Grade
Rating
375
400
5 (0.57)
500 (260)
750 (390)
-40 to +100
-55 to +125
-55 to +100
-65 to +125
Unit
Vdc
Vdc
in-lbs
°F (°C)
°F (°C)
°C
°C
°C
°C
Notes
Continuous
100ms
6 each, #4-40 or M3
<5 sec; wave solder
<7 sec; hand solder
Baseplate
Baseplate
Specifications
(typical at TBP = 25ºC, nominal line, 75% load, unless otherwise specified)
Compatible Products
• 2nd Generation 300V Input
DC-DC converters
Part Number Format
M-FIAM3 M 2 1
Product
Product Grade(°C)
H = –40 to +100
M = –55 to +100
Pin Style
1 = Short
2 = Long
*S=Short ModuMate
*N=Long ModuMate
Baseplate
1 = Slotted
2 = Threaded
3 = Thru-hole
Parameter
Min Typ Max
Input voltage
180Vdc 270Vdc 375Vdc
Output current
3A
Inrush limiting
0.018A/µF
Transient immunity
EMI:MIL-STD-461E
Conducted emissions: CE101, CE102
Conducted susceptibility: CS101, CS114, CS115, CS116
Dielectric withstand
1,500Vrms
2,121Vdc
Efficiency
96% 98%
Internal voltage drop
3.0Vdc 5.0Vdc
ON/OFF control
Enable (ON)
0.0Vdc
1.0Vdc
Disable (OFF)
3.5Vdc
5.0Vdc
External capacitance
10µF
22µF
Weight
3.1 (88) 4 (113)
Warranty
2
Remarks
Continuous
Exceeds limits of MIL-STD-704E
Input/Output to base
Input/Output to base
@ 3A, 100°C baseplate
Referenced to –Vout.
100kinternal pull-up resistor
See illustration C1 on page 3.
400V
Ounces (grams)
Years
*Compatible with SurfMate and InMate socketing systems.
Thermal Resistance
MTBF per MIL-HDBK-217F
Parameter
Baseplate to sink; flat, greased surface
Baseplate to sink; thermal pad (P/N 20264)
Baseplate to ambient
Baseplate to sink; 1000 LFM
Typ
0.16°C/Watt
0.1°C/Watt
7.9°C/Watt
2.2°C/Watt
Temp.
25°C
50°C
65°C
Environment
Ground benign:G.B.
Naval sheltered:N.S.
Airborne inhabited cargo:A.I.C.
MTBF
3,505,003
841,200
683,475
Unit
Hrs
Hrs
Hrs
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
MFIAM3
Set your site on VICOR at www.vicorpower.com
Rev. 1.5
Page 1 of 4



No Preview Available !

Environmental Qualification
Altitude
MIL-STD-810C, Method 500.2, Procedure I & II, 40,000 ft. and
70,000 ft. Operational.
Explosive Atmosphere
MIL-STD-810F, Method 511.4, Procedure I, Operational.
Vibration
MIL-STD-810F, Method 514.5, Procedure I, Category 14, Sine
and Random vibration per Table 514.5C for Helicopter AH-6J
Main Rotor with overall level of 5.6 grams for 4 hours per axis.
MIL-STD-810F, Method 514.5C, General Minimum Integrity
Curve per Figure 514.5C-17 with overall level of 7.7 grams
for 1 hour per axis.
Shock
MIL-STD-810-F, Method 516.5, Procedure I, Functional Shock,40 G's.
MIL-S-901D, Lightweight Hammer Shock, 3 impacts/axis, 1,3,5 ft.
MIL-STD-202F, Method 213B, 60 G's, 9ms half sine.
MIL-STD-202F, Method 213B, 75 G's, 11ms Saw Tooth Shock.
Acceleration
MIL-STD-810F, Method 513.5, Procedure II, table 513.5-II,
Operational, 2-7 G's, 6 directions.
Humidity
MIL-STD-810F, Method 507.4, Procedure I, Cycle I, 240 hrs, 95% RH.
Solder Test
MIL-STD-202F, Method 208, 8 hour aging.
Environmental Stress Screening
Operating Temp.
Storage Temp.
Temp. Cycling:*
Ambient Test
@ 25°C
Power Cycling
Burn-In:
Functional and
Parametric
ATE Tests:
Hi-Pot Test
Visual Inspection:
Test Data
H Grade
-40°C to +100°C
-55°C to +125°C
12 cycles
-65°C to +100°C
Yes
12 hours,
28 cycles
-40°C and
+100°C
Yes
Yes
vicorpower.com
M Grade
-55°C to +100°C
-65°C to +125°C
12 cycles
-65°C to +100°C
Yes
24 hours,
56 cycles
-55°C and
+100°C
Yes
Yes
vicorpower.com
*Temperature cycled with power off, 17°C per minute rate of change.
Conducted Noise
Transient Immunity
Figure 1– M-FIAM3 and Model V300A48M500AL
DC-DC converter operating at 180Vdc, 130W.
Inrush Limiting
Output
Input
Figure 2 – Transient Immunity: M-FIAM3 output response to
an input transient.
Figure 3– Inrush Limiting: Inrush current with 22µF external
capacitance.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
MFIAM3
Set your site on VICOR at www.vicorpower.com
Rev. 1.5
Page 2 of 4



No Preview Available !

Transient and Surge Protection
Note: The M-FIAM3 is shown in the on state. To disable,
open the connection between ON/OFF and –Out.
–IN
MOV P/N
03040
+IN
––
ON
EMI OFF
GND
M-FIAM3 NC
NC NC
++
C1
–IN –OUT
PR 2nd Generation
–S
300Vdc Input
SC
PC DC-DC Converters
+S
+IN +OUT
Capacitance (C1)
10µF(min),22µF(max)
Recommended Fuse:
3A Max., F03A Type
Mechanical Diagram
Module Pins
No. Function
Label
1 +In
+
2
No
Connection
NC
3 Ground EMI/GND
4 – In
5 – Out
6 ON/OFF ON/OFF
7
No
Connection
NC
8
No
Connection
NC
9 +Out
+
Slotted (Style 1)
or
Threaded (Style 2)
4-40 UNC-2B (6X)
or
Thru Hole (Style 3)
#30 Drill Thru (6X)
(0.1285)
0.50 ±0.02
12,7 ±0,5
0.23
5,8 (REF)
0.300 ±0.015
7,62 ±0,38
2.20
55,9
1.74
44,2
style 2 & 3
baseplates only
(4X)***
0.12* 0.20**
3,1 5,1
0.01
0.49
12,4
0.300 ±0.015
7,62 ±0,38
12
34
9 876 5
0.400
10,16
0.700
17,78
1.000
25,40
1.400
35,56
1.900
48,26
0.150
3,81
DIA,(2X)
0.080 DIA,(7X)
2,03
0.35
8,8
(2X)
0.65
ALUMINUM
2.28
16,5
1.30
BASEPLATE 57,9 33,0
0.43
10,9
R 0.06 (3X)
1,5
0.54
13,7
(9X)
Pin Style 1&S
(Short Pin)
0.62
15,7 (9X)Pin Style 2&N
(Long Pin)
* Style 1 baseplate only
** Style 2 & 3 baseplates
*** Reserved for Vicor accessories
Not for mounting
PCB Mounting Specifications
2.000
50,80
2.20
55,9
(REF.)
0.10
2,5
0.10
2,5
X
45˚
CHAMFER
FULL R (6X)
0.130 (6X)
3,30
Use a 4-40 Screw (6X)
Torque to:
5 in-lbs
.57 N-m
PCB THICKNESS 0.062 ±0.010
1,57 ±0,25
R 0.06 (4X)
1,5
1.790
45,47
PLATED
THRU HOLE
DIA
0.158
4,01
12
34
1.900*
48.,26
1.584*
40,23
9 87 6 5
INBOARD
SOLDER
MOUNT
PIN STYLE 1&S
(7X) 0.094 ±0.003
2,39 ±0,08
(2X) 0.164 ±0.003
4,16 ±0,08
ONBOARD
SOLDER
MOUNT
PIN STYLE 2&N
0.094 ±0.003
2,39 ±0,08
0.164 ±0.003
4,16 ±0,08
ALL MARKINGS
THIS SURFACE
ALUMINUM
BASEPLATE
PINS STYLES
STYLE 1 & 2: TIN/LEAD
HOT SOLDER DIPPED
STYLE S & N: GOLD PLATED COPPER
0.400*
10,16
0.195
4,95
0.700*
17,78
1.000*
25,40
1.400*
35,56
* DENOTES
TOL = ±0.003
±0,08
0.43
10,9
0.53
13,5
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
MFIAM3
Set your site on VICOR at www.vicorpower.com
Rev. 1.5
Page 3 of 4



No Preview Available !

Vicor’s comprehensive line of power solutions includes modular, high
density DC-DC converters and accessory components, configurable power
supplies, and custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is
assumed by Vicor for its use. No license is granted by implication or otherwise under any patent or patent
rights of Vicor. Vicor components are not designed to be used in applications, such as life support systems,
wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and
Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Component Solutions
for Your Power System
Vicor Corporation
25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
978-470-2900
Fax: 978-475-6715
Email
Vicor Express: vicorexp@vicr.com
Technical Support: apps@vicr.com
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
FARM, Filter/Autoranging Rectifier Module
Set your site on VICOR at www.vicorpower.com
Rev. 1.5
04/03/10M



M-FIAM3M11 datasheet pdf
Download PDF
M-FIAM3M11 pdf
View PDF for Mobile


Related : Start with M-FIAM3M1 Part Numbers by
M-FIAM3M11 Military 270Vin Filter Input Attenuator Module M-FIAM3M11
Vicor Corporation
M-FIAM3M11 pdf
M-FIAM3M12 Military 270Vin Filter Input Attenuator Module M-FIAM3M12
Vicor Corporation
M-FIAM3M12 pdf
M-FIAM3M13 Military 270Vin Filter Input Attenuator Module M-FIAM3M13
Vicor Corporation
M-FIAM3M13 pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact