LV8013T Datasheet PDF - ON Semiconductor

www.Datasheet-PDF.com

LV8013T
ON Semiconductor

Part Number LV8013T
Description Forward/Reverse Motor Driver
Page 6 Pages


LV8013T datasheet pdf
Download PDF
LV8013T pdf
View PDF for Mobile

No Preview Available !

Ordering number: ENA0907B
LV8013T
Bi-CMOS IC
Forward/Reverse Motor Driver
http://onsemi.com
Overview
LV8013T is a 1ch forward/reverse motor driver IC using D-MOS FET for output stage. As MOS circuit is used, it
supports the PWM input. Its features are that the on resistance (0.3Ω typ) and current dissipation are low.
It also provides protection functions such as heat protection circuit and reduced voltage detection and is optimal for the
motors that need high-current.
Functions
1ch forward/reverse motor driver
Possible to respond to 3V control voltage and 6V motor voltage device
Low power consumption
Low ON resistance 0.5Ω
Built-in charge pump circuit
Built-in low voltage reset and thermal shutdown circuit
Four mode function forward/reverse, brake, stop.
Specifications
Maximum Ratings at Ta = 25°C, SGND = PGND = 0V
Parameter
Supply voltage (For load)
Symbol
VM max
Conditions
Ratings
-0.5 to 16
Unit
V
Supply voltage (For control)
Output current
Input voltage
Allowable power dissipation
VCC max
IO max
IO peak1
IO peak2
VIN max
Pd max
DC
t 100ms, f = 5Hz
t 10ms, f = 5Hz
Mounted on a specified board *
-0.5 to 6.0
1.2
2.0
3.8
-0.5 to VCC+0.5
800
V
A
A
A
V
mW
Operating temperature
Topr
-20 to +75
°C
Storage temperature
Tstg
-55 to +150
°C
*Specified board: 30mm × 50mm × 1.6mm, glass epoxy board.
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Semiconductor Components Industries, LLC, 2013
May, 2013
71812 SY/N2608 MS / 80107 MS PC B8-9208 No.A0907-1/6



No Preview Available !

LV8013T
Allowable Operating Conditions at Ta = 25°C, SGND = PGND = 0V
Parameter
Supply voltage (For load)
Supply voltage (For control)
Input signal voltage
Input signal frequency
Capacitor for charge pump
Symbol
VM
VCC
VIN
f max
C1, C2,
CVG1, CVG2
Duty = 50%
Conditions
Ratings
2.0 to 15.0
2.7 to 5.5
0 to VCC
200
0.001 to 0.1
Unit
V
V
V
kHz
μF
Electrical Characteristics at Ta = 25°C, VCC = 5.0V, VM = 12.0V, SGND = PGND = 0V, unless especially specified.
Parameter
Symbol
Conditions
Re- Ratings
Unit
marks
min
typ
max
Supply current for load at
standby 1
Supply current for load at
standby 2
Supply current for control at
standby
Current drain during operation 1
Current drain during operation 2
H-level input voltage
L-level input voltage
H-level input current
(IN1, IN2, TIN)
L-level input current
(IN1, IN2, TIN)
Pull-up resistance (EN)
IM1
IM2
ICO
IC1
IC2
VIH
VIL
IIH
IIL
RUP
EN = 0V
1
VCC = 0V, Each input = 0V
EN = 0V, IN1 = IN2 = 0V
1
2
VCC = 3.3V, EN = 3.3V, VG at no load
VCC = 5.0V, EN = 5V, VG at no load
2.7V VCC 5.5V
2.7V VCC 5.5V
VIN = 5V
VIN = 0V
3
3
4
4
4
12.5
0.6×VCC
0
12.5
-1.0
100
1.0 μA
1.0 μA
25 50 μA
0.6 1.0
0.7 1.2
VCC
0.2×VCC
25 50
mA
mA
V
V
μA
μA
200 400 kΩ
Pull-down resistance
(EN)
Output ON resistance
Charge pump voltage1
Charge pump voltage2
RDN
RON
VG1
VG2
Sum of ON resistances at top and
bottom
VCC×2 - 5.4V CLAMP circuit
VM + VG1 Voltage raising circuit
4
5
6
6
100 200 400 kΩ
0.3 0.5 Ω
5.15
5.4
5.65
V
17.1
17.4
17.6
V
Low-voltage detection operation
voltage
Thermal shutdown operation
temperature
Charge pump capacity 1
VCS
Tth
VG1LOAD
VCC voltage
Design guarantee
IG1 = 500μA
7
2.1 2.25
2.4 V
8 150 180 210 °C
9 5.0 5.3
V
Charge pump capacity 2
VG2LOAD
IG2 = 500μA
9
16.0
16.5
V
IG current dissipation
(Fin = 20kHz)
Charge pump start time
IG
TVG
CVG = 0.1μF
10
11
350 μA
1.0 ms
Output
block
Turn on time
Turn off time
TPLH
TPHL
12 0.5 1.0 μs
12 0.5 1.0 μs
TOUT
Turn on time
TON
C = 500pF
12 0.5 20 μs
Turn off time
TOFF
C = 500pF
12 0.5 20 μs
TOUT output voltage H
TOH
C = 500pF
VG2-0.1
VG2
V
TOUT output voltage L
TOL
C = 500pF
0.05
0.1 V
* Design guarantee : This characteristics is not measured.
Refer to next page for remarks.
No.A0907-2/6



No Preview Available !

LV8013T
Remarks
1. It shows current dissipation of VM pin in output OFF state.
2. It shows current dissipation of VCC pin in stand-by state.
(The standard current depends on EN pin pull-down resistor.)
3. It shows current dissipation of VCC pin in state of EN = 5V (stand-by), including current dissipation of VG pin.
4. IN1, IN2 and TIN pin are built-in pull-down resistor, EN pin is built-in pull-up resistor.
5. It shows sum of upper and lower saturation voltages of OUT pin.
6. It controls charge-pump oscillation and makes specified voltage.
7. When low voltage is detected, the lower output is turned OFF.
8. When thermal protection circuit is activated, the lower output is turned OFF.
When the heat temperature is fallen, it is turned ON again.
9. IG (VG pin load current) = 500μA
10. It shows VG pin current dissipation in state of PWM input for IN pin.
11. It specifies start-up time from 10% to 90% when VG is in non-load state
(when setting the capacitor between VG and GND to 0.1μF and VCC is 5V).
12. It specifies 10% to 90% for start-up and 90% to 10% for shut-down.
Package Dimensions
unit : mm (typ)
3260A
6.5
24 13
Pd max -- Ta
1000
Specified board: 30×50×1.6mm3
glass epoxy board.
800
1
(0.5)
0.5
12
0.22
0.15
600
400
200
480
SANYO : TSSOP24(225mil)
0
-20
0
20
40
60 75 80
100
Ambient temperature, Ta -- °C
Pin Assignment
24 23 22 21 20 19 18 17 16 15 14 13
LV8013T
1 2 3 4 5 6 7 8 9 10 11 12 Top view
No.A0907-3/6



No Preview Available !

Block Diagram
CH2
CL2
CH1
CL1
VM
VCC
IN1
IN2
EN
LV8013T
OSC,CHARGE_PUMP
Low-voltage
thermal
protection
CMOS
LOGIC
Deffused
resistor
VG1
VG2
TOUT
OUT1
OUT2
PGND
TIN
SGND
Truth Table
EN
IN1
IN2
TIN
OUT1
OUT2
TOUT
Charge Pump
Mode
HH -
LL
-
Brake
HL - HL -
Forward
LH-
H
LL-
LH
ZZ
-
-
ON
Reverse
Standby
- -L - -L
Tr-OFF
- -H - -H
Tr-ON
L - - - LLL
OFF
Standby
- : Don’t care, Z : High-Impedance
· Current drain becomes zero in the standby mode. (Leak current from EN pin is excluded)
· The output side becomes OFF, with motor drive stopped, during voltage reduction and thermal protection.
Also, the charge of VG2 is discharged with an internal circuit at decreasing voltage.
Pin Function
Pin No.
Pin name
6 C1L
Function
Voltage raising capacitor connection pin.
Equivalent circuit
VCC
C1L
5
C1H
Voltage raising capacitor connection pin.
VG1
8 IN1 · Driver output changeover.
9 IN2
11 TIN · TOUT output control pin.
(Built-in pull-down resistor)
C1H
VCC
200kΩ
Continued on next page.
No.A0907-4/6



LV8013T datasheet pdf
Download PDF
LV8013T pdf
View PDF for Mobile


Related : Start with LV8013 Part Numbers by
LV8013T Forward/Reverse Motor Driver LV8013T
Sanyo Semiconductors
LV8013T pdf
LV8013T Forward/Reverse Motor Driver LV8013T
ON Semiconductor
LV8013T pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact